The changes to the engine are indicative of the changes to the rest of the bike, in that outwardly it appears largely unchanged, while close examination reveals that very few parts are carried over. All of the changes were aimed at keeping the bombastic power of the 2011 bike, while boosting low to mid-range power to help with acceleration out of corners. With a completely new cylinderhead and crank – that has lost 20% of its weight – Kawasaki claim the new engine’s reduction in inertia allows it to spin-up much faster. The lighter crank has several other side-effects, too. Not only does it benefit acceleration, but with less sored energy in the crank, it can be decelerated faster, while cornering forces are reducing thanks to the reduction in the gyroscopic effect of the rotating mass. The new cylinderhead’s intake ports are straighter and wider to allow a greater volume of fuel/air mixture to flow more easily into the combustion chamber and to contribute to power production. The exhaust ports are also straighter and wider to allow the chamber to purge more efficiently. Both intake and exhaust ports are also polished to improve gas flow, while the larger diameter intake and exhaust valves are now made from titanium to reduce mass. Larger coolant passageways also help keep the extra heat generated under control. The engine has revised cam profiles to optimise valve overlap for a strong balance of torque and high-end power, while their chromoly construction further aids the weight reduction. The pistons are shorter and lighter with revised crowns while thicker cylinder walls and a rerouted cooling system have been proven improvements from the firms racing developments. And all of this has been done while still passing the strict Euro4 regulations for noise and emissions. The airbox is now two litres larger, at 10lires, giving the engine a large volume of air to draw from all helped by a ram-air intake which has been moved further forward for greater efficiency, and an air filter with a larger surface area and higher flow rate. All this conspires to deliver a claimed 207bhp (with ram air) at 13,000rpm, and 84ftlb torque at 11,500rpm. What else is new? Exhaust: Shedding weight was a priority, so the new bike uses titanium headers identical in size to the race bike. Kawasaki say this means trackday addicts and racers will only have to replace part of the exhaust to get a fully track-focussed system. There are now three catalysers to help the bike pass stringent Euro4 emissions and noise tests, while the silencer is also now titanium – not stainless steel. Chassis: The changes to the chassis are not as extensive as those to the engine but the headstock is mounted 7.5mm nearer to the rider, helping to place more weight over the front wheel for improved stability and turn-in. Resonance chambers in the frame help to keep intake noise under control. Electronics: The new bike gets the latest batch of control systems, all based around the Bosch Inertial Measurement Unit (IMU) which operates through five measured axes plus a calculated programme which allows the bike to know what is going on in terms of lean angle, pitch and yaw, acceleration and braking. Kawasaki have emptied a bucket of acronyms over this bike and that includes: new Sport-Kawasaki TRaction Control (S-KTRC), Kawasaki Launch Control Mode (KLCM), Kawasaki Intelligent anti-lock Brake System (KIBS), Kawasaki Quick Shifter (KQS), Kawasaki Engine Brake Control (KEBC). The bike also has an Ohlins electronic steering damper and a new power mode selection. Swingarm: Now 15.8mm longer than before, helping to put more weight over the front wheel and improve stability under braking and turn-in. Suspension: The new front suspension has been jointly developed by the WSB team and Showa, with their Balance Free Front Fork making its mass-production debut on the new ZX-10R. At the rear there’s the firm’s Balance Free Rear Cushion (BFRC) shock. The 43mm fork is said to offer increased ride comfort, braking stability, improved front-end feel, with each leg being independently adjustable for compression and rebound damping. Each leg boasts a separate compressed nitrogen gas canister at the fork bottom with damping force generated separately to the main tube in a different chamber. This allows the whole surface of the main piston to act as a pump, pushing oil towards the valves and keeping pressure more constant. Brakes: The front calipers are now top-of-the-range Brembo M50 cast aluminium monoblocs, radially-mounted and gripping 330mm twin discs via braided steel hoses. The discs are 200mm wider in diameter than the outgoing bike and they have grooves around the outer edge to increase their surface area and therefore cooling. At the rear a 220mm single disc is gripped by a single piston caliper and also gets steel braided brake lines. At both ends the once fashionable petal discs have succumbed to good old-fashioned round discs. New aerodynamics: A larger top fairing was requested by the WSB team to help improve high-speed stability and aerodynamic flow. Increased wind protection is claimed to help racers change position more easily under braking turns because the air is less turbulent. The windscreen is now fully supported by the fairing and shouldn’t vibrate as much as the current bike’s at high speed. Intakes at the side of the windscreen reduce negative air pressure in the c*ckpit to stabilise airflow and reduce helmet buffeting. A new front mudguard gets a stepped design helping to direct air to the radiator to increase cooling. The Facts – 2016 Kawasaki ZX-10R (ZX1000RGF/SGF) Engine 998cc Liquid-cooled, 4-stroke inline four, DOHC, 16-valve Bore & Stroke 76.0 x 55.0mm Compression ratio 13.0:1 Claimed power 207bhp @ 13,000rpm (with ram air effect) Claimed torque 84ftlb @ 11,500rpm Frame Twin spar, cast aluminium Front tyre 120/70ZR17M/C (58W) Rear Tyre 190/55ZR17M/C (75W) Front Suspension 43 mm inverted Balance Free Front Fork with external compression chamber, compression and rebound damping and spring preload adjustability, and top-out springs Rear suspension Horizontal Back-link with BFRC lite gas-charged shock, piggyback reservoir, compression and rebound damping and spring preload adjustability, and top-out spring Front brakes Dual semi-floating 330 mm discs, dual radial-mount Brembo M50 monobloc calipers Rear brakes Single 220 mm disc, single-bore pin-slide, aluminium piston Wheelbase 1440mm Seat height 835mm Kerb mass 206kg (with ABS) Fuel capacity 17litres
And still Honda will be playing catch up when all other manufactures have moved on .r1 gsxr apprilla BMW need I say more
Like it going to have a test ride on one when is it out? Looks planted rear end looks better and tank looks more sit in,
Thanks SW that's some right up mate, musts of taken you ages! Glad the screen has been addressed... Looks nice, can't wait to see what a non green one looks like Hmm 2016 race bike
Here you go Jimbo... Im a little disappointed, its heavier and the electronics package could have been better...
Thanks Matt.... Doesn't look as good as the outgoing black mate. Heavier? Sure? Perhaps why they are quoting ram air bhp? Why disappointed with electronics? Pretty much the works isn't it??
Yes mate its 11lbs heavier, its longer and wider.. I was hoping for the auto blipping down shifter along with a new dash, something like the R1 dash... Im more than happy with what i have....
11 lbs or kg? Is hat like for like with the non / abs versions Wheel base longer? Maybe longer swing arm to address power delivery and stability? Dash I'd agree.... Auto blipper down shift, cool, but with a slipper clutch really needed?? Sorry don't know the spec of the old one tbh Wider.... Well.... That's just down to personal taste
Extra weight is down to the ABS (a requirement for all 2016 Bikes in this segment now) and the 3 Exhaust CATS for the stringent Euro 4 emissions testing. All stuff that can be fecked off for Track use!
I have the current abs version which weighs 201kg against the new models 206 kg. The 2015 non abs weighs 198kg. The 5kg weight increase will be the longer swing arm, it and quicker shifter imo. Anything you add obviously adds weight.
Me too Col! Think only a special edition £40K Ducati has had Gas Forks previously on a production Road Bike. Jonny Rea guna be well on for a second WSBK Title in 2016 me Finx!
Think they might be gimmick for a bit of bike meet bragging rights? look trick but bet it ain't full spec
looks great the back end has finally been fixed as for them front forks daaaammmm. Brembo top spec callipers as well, interesting to see the new traction control system in play the one they have got now is already better than the BMW one and works flawless on mine cant wait to see the improvement
the worst part is this is based on the current bike. Honda had there chance in 2012 but what did we get some new suspension and some headlights. As for the SP....... face pam lol. Electronics and power Honda come on
I'm sure.... I just think they are trying to make them looks like full on gas forks, which they won't be?
