HM Quickshifter Installation - Help desperately needed please

Discussion in 'Mods, Upgrades, Accessories and Products' started by KPH, Apr 11, 2015.

Page 2 of 2
  1. KPH

    KPH Active Member

    Joined:
    Aug 17, 2014
    Messages:
    159
    Likes Received:
    23
    Yes, it is, although it looks more salmon and green than pink.

    Something that has really really helped a lot are the videos on the 2014 CBR track bike conversion by Sportsbike Track Gear - if you look on their Bazzaz install video, they show the very same cable.
     
    #21 KPH, Apr 24, 2015
  2. sps170373

    sps170373 Moderator
    Staff Member

    Joined:
    May 24, 2013
    Messages:
    7,860
    Likes Received:
    3,092
    You got any photos of where the data loom plugs into? Just fitting a GP shifter myself and nothing on hm website about where loom plugs into
     
    #22 sps170373, May 1, 2016
  3. RRoss

    RRoss Active Member

    Joined:
    Apr 28, 2013
    Messages:
    1,372
    Likes Received:
    428
    image.jpeg
    Best pic I could come up with. You can see the 2 plugs that I've separated,the HM loom fits in between them,plugs are shaped and can only fit 1 way if I remember right so it's not possible to get it wrong way round. There's a good earth point down near starter,tapped out m6,you just need a bolt and you're good to go.
     
    #23 RRoss, May 1, 2016
    • Thanks Thanks x 1
  4. si1000repsol

    si1000repsol Well-Known Member

    Joined:
    May 5, 2011
    Messages:
    1,673
    Likes Received:
    517
    Image1462114594.950130.jpg
    It's a random pic but if I recall this is the plug on the gearbox speed sensor.
     
    #24 si1000repsol, May 1, 2016
  5. sps170373

    sps170373 Moderator
    Staff Member

    Joined:
    May 24, 2013
    Messages:
    7,860
    Likes Received:
    3,092
    Have earthed the unit ok using the main earth point, already had coil loom fitted from my plus model was just where the data loom plugged into

    Thanks for the picture! Have you one of where you sited the control unit please?
     
    #25 sps170373, May 1, 2016
  6. RRoss

    RRoss Active Member

    Joined:
    Apr 28, 2013
    Messages:
    1,372
    Likes Received:
    428
    I've got it sitting behind seat infill panel,didn't want it out on show but easy enough to get to.
     
    #26 RRoss, May 1, 2016
    • Thanks Thanks x 1
  7. si1000repsol

    si1000repsol Well-Known Member

    Joined:
    May 5, 2011
    Messages:
    1,673
    Likes Received:
    517
    #27 si1000repsol, May 1, 2016
  8. sps170373

    sps170373 Moderator
    Staff Member

    Joined:
    May 24, 2013
    Messages:
    7,860
    Likes Received:
    3,092
    #28 sps170373, May 1, 2016
  9. si1000repsol

    si1000repsol Well-Known Member

    Joined:
    May 5, 2011
    Messages:
    1,673
    Likes Received:
    517
    I was either going to use the sprocket cover bolt or the gear shaft bolt.
     
    #29 si1000repsol, May 1, 2016
Page 2 of 2

Share This Page