large rad stock fairings 08 blade

Discussion in 'Mods, Upgrades, Accessories and Products' started by Leroy preston, Dec 28, 2019.

  1. Leroy preston

    Leroy preston Member

    Joined:
    Feb 25, 2018
    Messages:
    85
    Likes Received:
    96
    So Iv purchased a 2014 engine to replace mine.

    it’s got
    Polished and ported head
    Upgraded valves and springs
    Suter slipper clutch and has been fully rebuilt.

    Apparently I would Benefit from a larger rad but would it fit?

    don’t really want track fairings as I still want to use the bike on the road.

    anyone have any ideas what I can do?
     
  2. Bikeboy

    Bikeboy Active Member

    Joined:
    Jun 14, 2018
    Messages:
    580
    Likes Received:
    231
    If you've not had any block/piston work .I dont really see why you would need a larger rad?
    Does your bike over heat,?
     
    • Agree Agree x 1
  3. Leroy preston

    Leroy preston Member

    Joined:
    Feb 25, 2018
    Messages:
    85
    Likes Received:
    96
    im still running the 08 engine.
    The new engine runs more power than my stock one. but to tell you the truth this is all new to me.
     
    • Friendly Friendly x 1
  4. nigelrb

    nigelrb Elite Member

    Joined:
    Nov 2, 2017
    Messages:
    9,804
    Likes Received:
    3,372
    Unless you're running much higher compression with increased fuel flow, you're hardly going to have any temperature variation at all. To the contrary in fact, because a P & P head will flow exhaust gases quicker resulting in less residual heat.

    Unless you're doing track in Qatar or Abu Dhabi you won't need a bigger rad. Perhaps the best mod might be if you're having the bike dyno'd, get them to tweak the ECU so the fan comes on earlier. Not exactly sure if this can be done with stock ECU though. With Woolich you can.
     
    • Like Like x 1
  5. Leroy preston

    Leroy preston Member

    Joined:
    Feb 25, 2018
    Messages:
    85
    Likes Received:
    96
    fair comments, I’ll certainly give it a go and if I have heat problems I’ll look at the larger rad.

    yes you are correct you can certainly programme the ecu for the fans to come on at a lower temp.

    the only other thing I’m worried about is the ecu and exhaust. I currently have a full yoshi system and I’m told it will work with the 14 engine and apparently the ecu after a map.
    I hope I don’t get any surprises lol thank you for the reply
     
    • Thanks Thanks x 1
  6. nigelrb

    nigelrb Elite Member

    Joined:
    Nov 2, 2017
    Messages:
    9,804
    Likes Received:
    3,372
    I think that would help a 'worked' engine much better than a standard one. You're on a winner with that. ;)
     
    • Like Like x 1
  7. Leroy preston

    Leroy preston Member

    Joined:
    Feb 25, 2018
    Messages:
    85
    Likes Received:
    96
    fingers crossed. I thought I was finished spending money on it I’m not sure it will ever end
     
  8. nigelrb

    nigelrb Elite Member

    Joined:
    Nov 2, 2017
    Messages:
    9,804
    Likes Received:
    3,372
    It doesn't. Just when you think the bike is spot on, some member puts up a post of irresistible goodies or bling, and the whole process starts again.

    I've been 'sucked in';) to buying a bespoke Red Bull helmet, a mint RST leather jacket, a carbon rear hugger, a promo crystal Honda Dream, and even an aprilia RSV1000RF.

    People just don't stop taking advantage of me. :(;);)
     
    • Like Like x 1
    • Agree Agree x 1
  9. Leroy preston

    Leroy preston Member

    Joined:
    Feb 25, 2018
    Messages:
    85
    Likes Received:
    96
    Sounds like you have plenty of toys!
    To be fair there’s not much left to do on my bike after this. I think I have nearly every mod going. Cost a fortune and I don’t get to ride nearly enough.
    But I do have a nice little trip planned in June
     

Share This Page