Data tool S4 removal

Discussion in 'Mods, Upgrades, Accessories and Products' started by Twisted2014, Jan 3, 2016.

Page 3 of 3
  1. Twisted2014

    Twisted2014 Active Member

    Joined:
    May 4, 2014
    Messages:
    89
    Likes Received:
    17
    I managed to remove it however then the bike didn't start. Had to send the bike to a garage to get it sorted.


    Sent from my iPhone using Tapatalk
     
    #41 Twisted2014, Apr 12, 2016
  2. Ibrahimsarmad

    Ibrahimsarmad New Member

    Joined:
    Apr 12, 2016
    Messages:
    10
    Likes Received:
    0
    Dear, I am in a country were there is no honda dealer or datatool dealer where I can send my bike to get it repaired. So if possible please guide me in removing it.
    Best Regards
     
    #42 Ibrahimsarmad, Apr 12, 2016
  3. Twisted2014

    Twisted2014 Active Member

    Joined:
    May 4, 2014
    Messages:
    89
    Likes Received:
    17
    Where are you based?


    Sent from my iPhone using Tapatalk
     
    #43 Twisted2014, Apr 12, 2016
  4. Ibrahimsarmad

    Ibrahimsarmad New Member

    Joined:
    Apr 12, 2016
    Messages:
    10
    Likes Received:
    0
    I'm from pakistan
     
    #44 Ibrahimsarmad, Apr 12, 2016
  5. Ibrahimsarmad

    Ibrahimsarmad New Member

    Joined:
    Apr 12, 2016
    Messages:
    10
    Likes Received:
    0
    .
     

    Attached Files:

    #45 Ibrahimsarmad, Apr 12, 2016
  6. blake7

    blake7 Active Member

    Joined:
    Feb 16, 2011
    Messages:
    685
    Likes Received:
    158
    Just follow the cable from the main unit which is located in the tail section. It goes to a plug under the tank close to the earth point. Just unplug it and job done.
     
    #46 blake7, Apr 12, 2016
  7. Ibrahimsarmad

    Ibrahimsarmad New Member

    Joined:
    Apr 12, 2016
    Messages:
    10
    Likes Received:
    0
    Dear, which plug are you talking about?
     
    #47 Ibrahimsarmad, Apr 13, 2016
  8. Ibrahimsarmad

    Ibrahimsarmad New Member

    Joined:
    Apr 12, 2016
    Messages:
    10
    Likes Received:
    0
    This red plug?
     

    Attached Files:

    #48 Ibrahimsarmad, Apr 13, 2016
  9. blake7

    blake7 Active Member

    Joined:
    Feb 16, 2011
    Messages:
    685
    Likes Received:
    158
    No, that is the crankshaft position sensor I think. You are looking for a white connector, mine was located on the left hand side of your photo, close to the main loom in the plastic holder.

    Are you sure yours is a Green and not Red alarm? I think the Red is an immobiliser, but the green is just an alarm, hence why you can just unplug it.
     
    #49 blake7, Apr 13, 2016
  10. Ibrahimsarmad

    Ibrahimsarmad New Member

    Joined:
    Apr 12, 2016
    Messages:
    10
    Likes Received:
    0
    Mine is s4 green but can't see any white connector
     
    #50 Ibrahimsarmad, Apr 13, 2016
  11. Ibrahimsarmad

    Ibrahimsarmad New Member

    Joined:
    Apr 12, 2016
    Messages:
    10
    Likes Received:
    0
    Where in the key is transponder located?
     

    Attached Files:

    #51 Ibrahimsarmad, Apr 13, 2016
Page 3 of 3

Share This Page